Replacing Lock on uPVC Door
If you're looking to change the lock on your upvc door you'll first need to take off the handle and screw holes. This is typically simple to do.
The next step is to find the screw that holds the barrel in place. The screw is typically different in colour from the other screws and is located on the edges of the faceplate of the lock.
Remove the Cylinder
To change the lock on your doors made of upvc first, you need to take off the cylinder that is currently in use. This is a relatively easy process that can be done in around 30 minutes. All you need is a screwdriver. The Euro Cylinder screw is normally found on the inside of the door next to the lock cylinder. The screw should be easy to identify as it is usually a different colour to the other screws. Remove this screw and keep it somewhere safe.
After the cylinder has been removed, you can start working on removing the handle. To accomplish this, you'll need to open the door wide enough that you can observe the inside edge of the door, as well as the side of lock faceplate.
Remove the screw that holds the handle to the door with the screwdriver. Once the screw is removed, you can pull the handle towards you, and then take the rest of it off the door.
If you're having trouble removing the handle from the door frame, you might have to unscrew it. This can be done with a drill or screwdriver, and you'll need to be careful not to cut the screw head or cross-thread it.
When you are ready to replace your cylinder, be sure that it is the right size for your door. Cylinders are measured according to two measurement points: (a) the distance from the middle of the Fixing Screw hole to the bottom of the cylinder and (b) the distance between the keyhole and the edge of the lock plate.
Remove the Handle
If your upvc door handle becomes stiff or loose, the good news is that this is a fairly easy problem to repair. The cause is usually down to wear and tear on the cylinder or internal components of the multipoint lock that are located inside the door between the handle and its frame. Weather conditions, heavy use or aging can cause upvc locks wear. This could lead to problems with the closing and locking mechanisms of the door.
The cylinder may wear out and make it difficult to turn the key. The lock may also become stiff, causing the handle to drop. The cylinder can be repaired, and is a simple process. This can be accomplished by yourself, however you will need to have some knowledge about how the mechanism functions. The first step is to remove the handle that will allow you to get access to the cylinder and replace it with a brand new one.
You'll need an screwdriver and a measuring tape for this. It is crucial to know the exact size of the cylinder you have in place to ensure that you get a replacement cylinder that fits. The cylinder is the element that locks your upvc door. Therefore, it is important that you ensure that you receive an identical replacement size.
To remove the old cylinder you will have to unscrew the screws that are holding it. Be upvc window lock repair cost not to strip out the screws, as this could make it difficult to remove the screws in the future. After the screws have been removed, the cylinder should be easy to remove.
Remove the Lock Barrel
uPVC doors are made with strong materials and are designed to keep your home safe and secure. They are available in a wide range of styles and colors that will fit into any home decor. They are also energy efficient and maintenance-free. However, they do have some drawbacks. As time passes, the locking point or barrel lock may become damaged and require replacement. This is a straightforward process however there are a few things to know prior to beginning.
To get to the screw that holds the lock cylinder, it is have to take off your door handle. It is typically colored differently from the other screws and can be found at the edges of the door, just where the keyhole is located. Remove the screw and place it in a safe location. Slide the handles out on both sides of the door. Be sure you do this slowly and not too fast, as it may harm your uPVC door.
After taking the handles off and removing the handles, you can use a screwdriver to take out the screws that secure the handles to the door frame. This will allow you better access to the support pins that are holding the cylinder. After that, you can try wiggling and tugging the cylindrical to see if it becomes loose. Once it does, pull it towards you and then remove it from the socket.
After removing the old lock cylinder, it is crucial to replace it with a new one which is anti-snap and anti-bump. It is best to have an expert locksmith do this for you, however you can do it yourself with the proper tools. This is a simple job that should take no more than five minutes.
Install the New Cylinder
A door lock made of upvc can be damaged or broken in a variety of ways, for instance, a tenant might have moved out but not returned the key, or the cylinder may have become damaged and cannot function as it should. Whatever the reason for changing your door lock made of upvc, it is crucial to select the right size replacement. If the wrong one is installed, your doors may be more vulnerable to the 'lock snapping method' which is responsible for 25 percent of burglaries.
It is crucial to choose the proper cylinder. The process is easy and takes just five minutes. You will need a screwdriver to take off the screws that are attached to the faceplate on the handle and the cylinder, but once you have done this it's a simple task to switch them.
Before you begin, make sure that the handle is in a position to open and you have full access to the inside of the edging of the door and the side of the handle faceplate which holds the lock cylinder. This will make sure that you are able to disconnect the lock cylinder, without needing to move the handle on the door to expose any internal parts of the handle frame.
Then, take out the old cylinder and take a measurement of it. You will need to know its overall length and the measurement of the cam that is used to lock or unlock the door. This will enable you to locate a new cylinder that's the same or smaller. This is the most crucial part of the entire process. A cylinder should be flush with the handle backplate and be no more than 5mm from it.
Install the Handle
A upvc lock can jam if something breaks inside the case that controls the bolts that retract into the keep plate or strike. Often this can be resolved by making an Allan key adjustment under the hinges of the door but occasionally this could put excessive pressure on the parts inside the centre case, so it is best to call a professional out.
It is important to have quick and easy access to both sides when you are changing the handle. It is important to use the right tools. It is also an excellent idea to prop the door open so that it doesn't close during this process.
The first step is to loosen the screws that hold the handle together using the help of a screwdriver. Once they are loose the handle can be removed. After taking off the cylinder and the handle, it's now time to install the replacement handle. Make sure the new handle is compatible with your existing center of the cylinder and cylinder. To determine the proper size take a measurement of the spindle's length on the lever that you currently have. Verify that the screw fix centre on the handle is identical to the screw fix centre of your existing hole centre or cylinder.
The replacement handles offered by Fab and Fixed are available in a range of styles and are built to last. These handles are perfect for those looking to upgrade their upvc handle and increase security for their home. Having the right handle will ensure that your home is secure and safe and will not be easy for thieves to break into.